Highest Quality Automotive Paints at Affordable Prices!!

MonoCoat 1K Direct to Rust

MonoCoat 1K Direct to Rust Urethane
  
A moisture-curing coating is a type of coating that cures due to the presence of moisture in the atmosphere. This coating forms a protective coating film by reacting chemically with the moisture in the air. It is designed to paint directly over sound rusted metal surfaces to stop rust permanently. Waterproof! Perfect for the marine environment. Impervious to chemicals, salt, and other corrosive contaminants and is able to be painted over rust.
This is nothing like POR15, this Mono cure technology supersedes any kind of POR15 products on the market.
Reduction not needed.

Monocoat is a high-performance, moisture-cured coating that encapsulates and stops rust from spreading.

Monocoat it designed to be top coated with almost any paint. In some areas you *could leave it as a Topcoat, but chalking can occur in direct sunlight.

Monocoat can be applied over bare metal or surface rusted areas. Brush or spray applied. It is ideal for any type of rusted metal surface and can handle temperatures up to 350 degrees. 

Can be used outdoors at temperatures as low as 40 degrees. Assuring excellent adhesion and impact resistance along with industry leading corrosion protection and encapsulating properties.

  • Mono component aluminum pigmented coating
  • 67% solids by weight
  • Approximate coverage: 96 SQ FT per quart for one coat
  • 1 coat assures maximum protection
  • Brush, roller or spray applied
  • Paint Gun: HVLP gravity or siphon with a 1.4 minimum needle/nozzle
  • Re-coat able after 4 hrs.- if top coating after 48 hrs., scuff surface with 320 grit paper
  • 2 hrs., tack free
  • Easy to apply
  • Topcoat able with virtually any high-quality coating
  • Maximum service temp of 350 Degrees 

TDS Sheets

TDS SHEET (COMING SOON)   Call 800 678 1533 Press # 3

^Click there ^ for pdf file

 

Q&A

Q&A will be added soon. Feel free to email suggestions

 

YouTube Videos

Customer Video:

https://www.youtube.com/watch?v=pbra3DYuHWM

Kit Includes:
1- Monocoat
(Single Component)

Customer Reviews

Based on 26 reviews
88%
(23)
8%
(2)
0%
(0)
0%
(0)
4%
(1)
J
Joel Leese
Tamco Monocoat is great

This penetrating paint goes a long way. Whatever you are painting make sure your piece is above 60 degrees. It loves warm metal. I used a heat gun to get my metal up to temp. It is Winter and my basement is around 55 degrees. Im painting suspension parts on my 2000 Mustang GT. I already started spraying topcoat on some of the parts and they look great. Great product.

D
David Hodson
Great undercarriage paint

The Monocoat went on perfect, I reduced it 15 percent and sprayed my frame and under body. After 24 hours you can’t dig your fingernail into it. Tough paint for sure

D
Derick bland
Covered more than I planned!

I bought a can. Planned a few parts and one inside fender engine well. Ended up doing both inner fenders, right front quarter if frame, control arms and under the hood as well as half the fire wall. Still had 1/4 of a can left. Can run pretty easy. Video says put it on thick. I did and got some runs. But as it's a bottom coat I'm not worried about them much.

M
Mathew Anderson

MonoCoat 1K Direct to Rust

D
David K
Excellent frame/suspension coating

Stuff went on glossy, but drys to a "satin sheen" I would say. Ended up looking perfect for an undercarriage. This stuff sticks better then any other product I've tried. I brushed on which came out great with only minor brush strokes in some places. After drying for 3 days I performed other repairs which had me spraying brake clean, and other caustic stuff on frame and scrubbing hard with a rag and this stuff didnt budge or look any different. This will be my go to product from here on out. Note: garage was 90 degrees and within 15 minutes it was practically dry or had consistancy of almost cured 2 part epoxy glue.
Thanks for this product.